Free Shipping Across Continental USA | Starts in

Days
Hours
Minutes
Seconds

Simple Assembly

For The Ocean Jungle Gym!

Jungle gyms offer children a fun and engaging way to develop physical and social skills, including strength, balance, coordination, communication, cooperation, and problem-solving.

Accessory Checklist

Part 1 - a

Assembly instructions

Let’s Begin

This step-by-step manual will guide you to put your Ocean Jungle Gym together! Once you’re done, your child is free to enjoy endless playtime possibilities!

Step 1

Place and secure twelve (12) wooden rods “H1” on two (2) wood pillar “G”. Insert and tighten six (6) screw “e” on each side of wooden rods “H1”.

Step 2

After installation, the climbing ladder would be display as shown in the diagram below.

Step 3

Place and secure the wooden arch “Q” to the ladder from Step 2. Place twelve (12) screws “e” on each wooden rods “H1” and tighten to the wooden arch “Q”.

Step 4

Complete the installation as shown in the diagram below.

Part 1 - b

Assembly instructions

Step 1

Place and secure wooden pillar “E” to wooden arch “Q”. Place two (2) screw caps “d” and two (2) screws “b” into wooden arch “Q”.

Step 2

After installation, the ocean jungle gym ladder would be display as shown in the diagram below.

Part 2

Assembly instructions

Step 1

Place one (1) wooden pillar “D2” together with wooden plank “P”. Tighten two (2) screws “b” and two (2) screw caps “d” to pillar “D2”.

Step 2

Place one (1) wooden pillar “H2” in wooden pillar “D2”. Use one (1) screw “a” tighten wooden rod “H2”, wooden pillar “D2” and wooden plank “P” together.

Step 3

Place net climber “K” to wooden plank “P”. Use one (1) screw “a”, two (2) screws “b” and two (2) screw caps “d” to tighten net climber “K” onto wooden plank “P”.

Step 4

Use one (1) screw “g” to tighten wooden pillar “E” with the bottom of net climber “K”.

Step 5

Place one (1) wooden rod “H2”, wooden pillar “E” and wooden pillar “D2” together, tighten them with one (1) screw “g”.

Step 6

Place wooden pillar “D1” onto wooden rods “H2”.

Step 7

Place two (2) screws “a” on wooden board “O” and tighten to wooden pilar “D1” and net climber “K”. Secure four (4) screws “b” & two (2) screw caps “d” to wooden board “O”, wooden pillar “D1” and net climber “K”.

Step 8

Tie and secure ladder “N” to the wooden rod “H2”.

Part 2

Assembly instructions

Step 1

Place and secure three (3) wooden rods “H1” to two (2) wood pillars (C). Please and tighten three (3) screws “e” on all wooden rod “H1” on each side of wooden pillar “C”.

Step 2

Complete the installation as shown in the diagram below.

Step 3

Place and secure wooden pillar “C” to wooden plank “P”.

Step 4

Place two (2) screws “b” with two (2) screws cap “d” on wooden pillar “C” to secure to wooden plank “P”. Place two (2) screws “b” with two (2) screws cap “d” on wooden pillar “C” to secure to wooden board “O”.

Step 5

Complete the installation as shown in the diagram
below.

Part 3

Assembly instructions

Step 1

To complete climber Part 1 and part 2, place and secure wooden pillars “G”
to wooden pillar “D1” and net climber “K”. Place two (2) screws “b” with two (2) screw caps “d” on and
tighten the top of the wooden pillars “G”. Use two 
(2) screws “g” to tighten the bottom of wooden pillars “G”.

Step 2

Complete the installation as shown in the diagram below.

Step 3

Place and secure two (2) wooden pillars “F” to wooden pillars “E”,
then use four (4) screws “e” to tighten them.

Part 4

Assembly instructions

Step 1

Place and secure two (2) wooden pillar “A” on both side of the wooden plank “L”. Screw and tighten three (3) screws “e” on both sides of the wooden pillar “A”.

Step 2

Complete the installation as shown in the diagram below.

Part 4

Assembly instructions

Step 1

Place and secure two (2) wooden pillar “B” to wooden plank “M”. Place and tighten four (4) screws “e” on both sides of the wooden pillar “B”.

Step 2

Place and secure six (6) blocks “J” on wooden plank “M”. Use two (2) screw “f” to screw in each blocks “J”.

Step 3

Finish the climbing board assembly
as shown in the diagram below.

Part 4

Assembly instructions

Step 1

Place one (1) screw “c” with screw cap “d” and tighten the wooden wheel “R”.
Insert the rope end of the swing “I” in to the holes on wooden plank “P”.

Step 2

Place the climbing board to the ladder. Place the slide/climbing board
on the ocean jungle gym to complete the installation.

Step 3

Complete the installation as shown in the diagram below.

It’s Playtime!

Search for Products

Search

Become an Ambassador

Please fill out the below form and One of our agents will be with you shortly.

Become an Influencer

Please fill out the below form and One of our agents will be with you shortly.

Become a Retailer

Please fill out the below form and One of our agents will be with you shortly.